Holly Springs Motorsports







Holly Springs Motorsports
Class Rules




Super Pro


 -  ET Break for Super Pro is 0-8.49 seconds in the 1/8th mile.



Footbrake

 -  No delay boxes in vehicle, must be removed.
 -  No transbrakes.
 -  There is not an ET Break for Footbrake.
 

Mean Street

 TIRE SIZE      Any 275 Drag Radial or 10.5 Slick NO W's

no wheelie bars!

Cap will be drawn from a hat before 1st Qualifying run   5.10 - 5.15 - 5.20 - 5.25 - 5.30

$800 winner / $300 runner up     Based on 10 cars

_____________________________________________________________________________________________________________

 X275
FORMAT:
This is a 1/8 mile heads-up class run on a .400 pro tree with a pro ladder.
32 CAR FIELD

BODY:
The car must retain its original appearance, profiles, and dimensions. Factory roof and quarter panels must be used. Aftermarket fiberglass and/or carbon fiber replacement panels are limited to hood, front fenders, doors, deck-lids, and bumpers only. All front ends must be of factory dimensions and cannot be lengthened and must meet all NHRA/IHRA height. (See ground clearance note below). Any beam tripping devices forward of the bumper are prohibited. (Track tech official will have final say) Aftermarket wings and spoilers are permitted. Complete stock appearing front and rear bumpers are required. A hood must be used: scoop or hood must cover the entire induction system. Forward facing hood scoops/ turbo or supercharger inlets are permitted.

GROUND CLEARANCE:
Minimum 3 inches from front of car to 12 inches behind centerline of front axle, 2 inches for remainder of car, except oil pan, oil retention device, and headers.

INTERIOR:
Factory appearing dashboard, door panels, and driver seat is required. Full Carpet is required on floorboards including transmission tunnel. Factory floor pan on driver and passenger side required from firewall to rear of door jamb. Transmission tunnel maybe removable and must be metal. Bare inside frame of car cannot be exposed. Aftermarket steering column is permitted.

WINDSHIELD/WINDOWS:
OEM glass or Lexan windows are permitted.

CHASSIS:
Complete stock chassis and frame rails must be retained from motor plate/shock tower to behind the rear wheel opening. Back-halved cars are not permitted. Front core support may be modified or removed. Aftermarket bolt-on replacement front K-members/sub frames are allowed (if front shocks bolt to K-member then they must be in factory location). Shock tower can be notched or trimmed but must be in factory location, verifiable by the factory sheet metal being retained between frame rail and top of tower. Mini tubs are allowed. Rear frame rails may be notched for clearance and must be in the factory location. Factory wheelbase must be maintained. (+ or � 1 inch)

ENGINE:
Maximum displacement for all engines is 588ci. Small blocks are allowed any deck height but must retain stock bore spacing. Big block allowed the following deck heights but must retain stock bore spacing. GM Big Blocks are limited to a 10.2 deck height. Ford Big Blocks are limited to a 10.3 deck height. Mopar Big Blocks are limited to a 10.7 deck height. (Cylinder head specs and list for BB Nitrous Combos attached)(Billet SB/BB blocks prohibited)

TURBOCHARGERS:
Single turbocharger limited to 88 mm maximum. (Garrett GTX55-88, Exile ETR-88, or = Forced Induction, Comp, Bullseye - mid frame or current (2013) Gen II Pro Mod MF88, PTE LF85 or LF88 turbos only). Turbocharger size will be verified by measuring the housing bore at the leading edge of the impeller wheel and must maintain the contour of the compressor housing. (Stepped or Clipped compressor wheel prohibited) Inducer dimensions will not exceed 3.462 inches and Exducer dimensions will not exceed 4.765 inches on MID FRAME turbos. Inducer dimensions will not exceed 3.462 inches and Exducer dimensions will not exceed 5.56 inches on LARGE FRAME turbos. The maximum diameter of the housing bore at the leading edge of the wheel may not exceed 2 mm more than the maximum allowable turbocharger size permitted. Inserts or reducers to achieve inlet or outlet dimensions prohibited. Any type of air to air or water to air intercooler permitted. Turbochargers w/nitrous-oxide prohibited except on 2-rotor, 4 cylinder, and inline 6 cylinder engines.

SUPERCHARGERS:
Cog or gear driven superchargers are permitted, must meet all factory inlet, outlet, and internal housing dimensions. Inserts or reducers to achieve inlet or outlet dimensions prohibited. Any type intercooler is permitted. Supercharger cannot be combined with nitrous oxide. Roots superchargers are limited to a 10-71. Centrifugal superchargers are permitted. Screw superchargers are not permitted.

NITROUS OXIDE:
Small block is permitted to run any type multi-stage nitrous systems. Big blocks are limited to a single stage nitrous system with single 10 lbs. or 15 lbs. bottle and single -8 line (-6** with cold nitrous)(**see below for accepted line) to fogger single wye to -6 line(**see below for accepted line) (-4 with cold nitrous) connected to fogger solenoids or single -8 line (** see below for accepted line -6 line if using cold nitrous) to plate solenoid(s) � A single stage fogger (2 nitrous solenoids and 2 fuel solenoids) are permitted or if using a single plate then your limited to (1 fuel solenoid, 1 nitrous solenoid), and 1 purge solenoid, purge must exit engine compartment. Big Block & Small block nitrous are permitted water injection. All EFI Big Blocks will only be allowed 2 nitrous solenoids for a dry nitrous system and will only have 1 line per nozzle/per cylinder. (Using both sides of the fogger nozzle on a dry EFI NOS BB combo are prohibited)(Cold nitrous systems permitted on big block combo and permitted on small block combo) All lines on big block combo must be visible and continuous from bottle to wye without interruption.

TRANSMISSION:
Any factory style automatic transmission allowed. OEM factory style manual transmission allowed. Bruno-Lenco transmissions are prohibited. Aftermarket clutch-less manual transmission and clutch assisted manual transmissions are permitted on naturally aspirated and nitrous small block combinations only. Electric shifters or air shifters are permitted.

INDUCTION:
Small Block combinations may run any type induction. Big Block combinations are limited to a dedicated single opening cast intake with a single carb or a single 4150 or 4500 series throttle body. (4 blade, dual blade or single blade throttle body permitted).

OILING SYSTEM:
Dry sump oiling systems are permitted on all cars

EXHAUST:
Mufflers or inserts are required on all cars except for turbo cars. Exhaust may exit underneath car or out the front fenders but must not affect timing or staging beams.

FUEL:
Gasoline only is permitted. Alcohol/E85 permitted on roots blown/V6/Inline-6/4cyl applications. Alcohol or E-85 or other derivatives is prohibited on all other combinations. Meth injection prohibited. Water injection permitted on SB NOS combos only.

STREET EQUIPMENT:
Functional headlights, taillights and brake lights required. All headlights, brake lights, etc. must be on car and not removed for any reason. All vehicles may be towed back from their passes.

SUSPENSION:
Stock style or ladder bar suspension cars only. Aftermarket four links are prohibited on all cars. Aftermarket direct replacement components such as: front control arms, rear control arms, front coil over shocks, and rear coil over shocks are permitted. Aftermarket rack and pinion steering allowed. Rear leaf springs, springs, shocks, and coil-overs may be moved to accommodate tire clearance, and do not need to be mounted in stock location. Bolt-on or welded sub-frame connectors, rear sway bars, are permitted on all cars. Wheelie bars are prohibited on all cars. Torque arms are only permitted on cars that were originally equipped from factory with it. (see notes below) Upper and Lower control arms must be mounted in the factory chassis locations -S Box permitted.

TIRES:
All cars with power adder must compete on a Drag Radial type tire with the following sidewall designation 275/60/15. Naturally aspirated combos are permitted to run a 28.0� x 10.5� slick, no �W� tires permitted.
MINIMUM BASE WEIGHTS (SVA applies to 23* GM 20* Ford 18* Mopar 15* LS heads)

*All minimum base weights include the driver. 

� NA Small Block 2300 lbs.

� NA Big Block up to 648 cu in � stock bore space any cylinder head-any intake 2600 lbs.

� Nitrous Small Block 2600 lbs.

� Nitrous Big Block w/ single stage diffuser or cross bar type single stage plate 9.8 deck height & conventional heads 3000 lbs. (add 50 lbs. for GM 9.801 and up deck height)

� Nitrous Big Block w/ nozzle type plate 9.8 deck height & conventional heads 3050 lbs. (add 50 lbs. for GM 9.801 and up deck height)

� Nitrous Big Block w/ single stage fogger single bottle w -8 feed and -6 lines after the wye or single -6 feed with -4 lines after wye with cold nitrous 9.8 deck height & conventional heads 3200 lbs. (add 50 lbs. for GM 9.801 and up deck height)

� Single YSI/F1A/6-71 Supercharger (small block-any cylinder head) 2700 lbs. (M1 permitted)

� Single F1C-94/8-71 Supercharger (small block-any cylinder head) 2800 lbs. (add 50 lbs. for F1C-10.5)(M1 permitted)

� Single F1R/Cast Xi/10-71 Supercharger (small block � any cylinder head) 2900 lbs. (deduct 50 lbs. for mod motor � 8.2/8.7 deck and/or cast inline SVA) (M1 permitted)

� Single Billet Xi Supercharger (small block � mod motor � cast inline SVA) 3050 lbs. (deduct 50 lbs. for 8.2/8.7 deck)

� Single Billet Xi Supercharger (small block � inline cast head) 3150 lbs. (deduct 50 lbs. for 8.2/8.7 deck)

� Single Billet Xi Supercharger (small block � non-inline head) 3250 lbs. (deduct 50 lbs for 8.2/8.7 deck)

� Single F1X/XB105 Supercharger (small block � mod motor, cast inline SVA including 15*LS) 3200 lbs. (deduct 50 lbs. for 8.2/8.7 deck)

� Single F1X/XB105 Supercharger (small block � inline head � C3/SB2) 3250 lbs. (deduct 50 lbs. for 8.2/8.7 deck � no deck height deduct for C3)

� Single F1X/XB105 Supercharger (small block Mopar Hemi) 3300 lbs.

� Single F1X/XB105 Supercharger (small block � non inline cast head) 3350 lbs. (deduct 50 lbs. for 8.2/8.7 deck)

� Single 76mm T6 Turbocharger (mid frame GT47 based) (small block) 2700 lbs. (M1 permitted)

� Single 80mm T6 Turbocharger (mid frame GT47 based) (small block) 2750 lbs. (M1 permitted) (Add 150 lbs. for billet wheel Garrett/Forced Inductions GTX-55/80 with max 130 mm Compressor Exducer)

� Single 83mm T6 Turbocharger (mid frame GT47 based) (small block) 2800 lbs.

� Single 85mm T6 Turbocharger (small block) (Large Frame 85/GTX55/85 w 117mm Compressor Exducer) 3100 lbs. (deduct 50 lbs. for 8.2 deck/mod motor)(deduct 50 lbs. for cast inline SVA head)

� Single 85mm T6 Turbocharger (PTE Pro Mod 85) (small block) 3250 lbs. (deduct 50 lbs. for 8.2 deck/mod motor)(deduct 50 lbs. for cast inline SVA head)

� Single 88mm T6 Turbocharger (Y2K or GT47-88)(small block) 2900 lbs. (any head)

� Single 88mm T6 Turbocharger (Large Frame 88/GTX55/88 w 117 mm compressor Exducer)(small block) 3250 lbs. (deduct 50 lbs. for 8.2 deck/mod motor)(deduct 50 lbs. for cast inline SVA head)

� Single 88mm T6 Turbocharger (PTE Pro Mod 88) (small block) 3350 lbs. (deduct 50 lbs. for 8.2 deck/mod motor)(deduct 50 lbs. for cast inline SVA head)

� *Small Blocks (NOS & NA) with single 4150 carb/throttle body: deduct 50 lbs.

� *Small Block (NOS) with any plate system: deduct 50 lbs. (does not apply if used in conjunction with a fogger)

� *Small Blocks (NOS & NA) with 23 degree Chevy heads, 20 degree Ford heads, and 18 degree Mopar heads: deduct 100 lbs. Raised Runner -75 lbs.

� *Small Block (NOS only) 18 -10 degree valve angle inline head: deduct 50 lbs.

� *Small Block (NOS only) cast Tunnel Ram/Sheet Metal 2 carbs � 2 throttle bodies: add 50 lbs.

� *Throttle bodies exceeding 4500 series on Big Block NOS combinations: add 50 lbs.

� *Non Intercooled boosted cars on gasoline: deduct 100 lbs.

� * Belt driven centrifugal and roots style superchargers: deduct 100 lbs.

� *Aftermarket rear suspension COPO Chevy and Drag Pack Mopar permitted on the new Camaro and Challengers must be mounted in exact factory location on body/frame. Torque arm on late model GTO and 5th gen Camaro permitted. Corvette with any leaf spring or ladder bar type suspension permitted.

� * Buick/Olds/Pontiac/Mopar B1 Nitrous Combo will be 3000 lbs. and not exceed 588 cubic inches.

� V6/I6/I4 turbocharged � supercharged � nitrous combos will deduct 250 lbs. from base weight on gas and 150 lbs. if on alcohol.

� Factory IRS deduct 100 lbs.

**Cold Nitrous -6 and -4 nitrous line(s) must be of standard braided line construction, (high pressure hydraulic line prohibited as they exceed the internal diameter of industry standard)
Standard spec lines/fittings only.
Lines
-4 I.D. .153 to .154
-4 I.D. with -6 Nut .153 to .154
-6 I.D. .275 to .276
Big Block Chevy Cylinder Head:
Conventional Heads as referenced to the original Mark IV design. (BBC symmetrical or raised port design is not defined as conventional for these rules)
- Stock port location/Standard port location � no raised runner
- Floor of port may not be more than .550 from deck
- No port plates or intake manifold adapter plates permitted
- No epoxy or welding permitted except for repair in chambers or between cylinders
- No welding of tops of runners except for adding bolt bosses for rocker stands
- Intake valve angle will measure 24* + or � 1*
- Maximum dimension allowable from deck surface to the top of the intake port will be no more than 3.125�
- Heads with �AS CAST� intake port lower than this dimension will be permitted.
- No welding or epoxy permitted to achieve this dimension.
- Tech official has final say at the time of inspection on any issues that may arise
Suggested castings to include the following:
� CFE/BMF 350 � 405cc Big Block Chevrolet
Chevrolet Factory OEM Iron & Aluminum; OEM Aluminum
� Brodix BB-1, BB-1 OEF1, BB-2, BB-2X, BB-2 Extra, BB-2 Plus, BB-3, BB3X, SR23 (non-raised runner Head Hunter)
� Edelbrock MC - Victor & Victor CNC, Edelbrock Victor Jr. CNC Oval & Rect
� Edelbrock Performer RPM 454-O, 454-O, 454-R
� Edelbrock Victor 24-degree Rectangular Port #77419, #77409
� Edelbrock RPM XT Rectangle PN#51539
� Edelbrock RPM XT Oval PN#51459
� Edelbrock Victor PN#61409
� Edelbrock Victor PN#61419
� Edelbrock Victor PN#77609
Pro � Filer Sniper and SniperX 290 cc 320 cc and 375 cc
� Dart Pro 1 310 cc thru 355 cc, Race Series 265 cc thru 360 cc, Dart 380 Pro2
� Canfield Big Block Chevy 24.5-800, 24.5-900
� GMPP Signature Series BB Heads cast # 12363401, 12363391
� Air Flow Research 265, 290, 305, 315, 325, 335, 345, 357, 385, Oval, Rect & CNC Port
� World Products Merlin II Oval & Rect Port 269, 320, 345, 305, 350 Iron & Alum
� (RHS)Pro Top Line Pro Thunder 320, 360 cc Alum & Iron
Big Block Ford Cylinder Head:
- Factory cast Iron heads (don�t think we�ll see many of them )
- A-429 Cobra Jet (Ford Motorsports)
- Cobra Jet (Blue Thunder, Trick Flow)
- Super Cobra Jet (Ford Motorsports, FRPP/Kaase)
- Blue Thunder �B� head
- Street Heat (Trick Flow)
- Edelbrock RPM
- P-51's (Kaase)
- �A� designation heads (All manufacturers, Ford Motorsports, FRPP, Trick Flow, Eliminator, EX514, etc. . .)
Big Block Mopar:
B-1 style cylinder heads only


PRO 275

ANY TRANSMISSION PERMITTED
DUAL POWER ADDERS (PROHIBITED)
TIRES 275 drag radial
  OR 315 drag radial add 50#

ANY REAR SUSPENSION
NO WHEELIE BARS
NO PRO MOD CHASSIS / STOCK WHEELBASE ONLY / STOCK APPEARING BODIES
SB N/A 2100
BB N/A 2300 LBS
SB NOS 2350 LBS
BB NOS 2500 4.840 BORE ENGINES
BB NOS 2650 LBS 5.00 BORE ENGINES
BB NOS 2750 LBS OVER 5.0 BORE ENGINES
SB SINGLE TURBO 2750 LBS
SB TWIN TURBO 2850 LBS
SB TWIN TURBO (500 CU IN +) 3000LBS
SB PROCHARGER 2725 LBS
BB PROCHARGER F3 2900 LBS, F2 2800 LBS, F1 2700 LBS
BB TWIN TURBO 3150 LBS (94'S OR SMALLER)
BB TWIN TURBO 3250 LBS (98'S)MAX TURBO SIZE
BB TWIN SUPERCHARGER 2950 LBS
BB Single Turbo 2850 LBS
4 cyl. and 6 cyl. combos 2650 LBS (Production Engines Only)
BB ROOTS BLOWER 2750 LBS
SB ROOTS BLOWER 2725
SB SCREW 2750
BB SCREW 3150 LBS
315 Tire add 50 LBS






MX235
Format:
This is an 1/8 mile, heads-up class run on a .400 Pro Tree with a Professional Ladder. Auto-Start and Courtesy Staging are in effect. MX235 will pit the Top 16 Qualifiers against each other in the "Front Runner" category. Cars that did not qualify in the 16 Car Field may be eligible for a "Second Chance" race. All-Run format may be used at certain events.

Safety:
All NHRA/IHRA and Local Track Safety rules apply for driver and car, including the use of an oil retention device or engine diaper is mandatory.

Chassis:
Complete stock chassis and front frame rails must be retained from motor plate/shock tower to behind the rear wheel opening (for non back-halved cars only). Back-halved cars are permitted. All aftermarket front suspension components are allowed. All replacement parts must be in stock location. Aftermarket bolt-on replacement front K-Members/Sub Frames are allowed. Struts or relocated shocks are permitted. All aftermarket bolt-on front ends are legal. Mini tubs are permitted. Anti-Sway Bars are allowed. Relocation of rear shocks are allowed. Rear leaf springs, springs, shocks and coil-overs may be moved to accommodate tire clearance and do not need to be mounted in stock location. Stock suspension, ladder bar and torque arm only. Aftermarket 4-Links are prohibited. Wheelie Bars are prohibited. Factory wheel base must be maintained.

Interior/Body:
Factory Appearing (aftermarket parts are allowed) interior is required. Factory floor pan on driver and passenger side required from firewall to rear of door jamb. Firewall must be in stock location; minor modifications for transmission, etc. are accepted. Headlights and Taillights must be functional. Aftermarket fiberglass and/or carbon fiber replacement panels will be limited to hoods, front fenders, doors, deck-lids and bumpers only. All front ends must be factory appearance and cannot be stretched. No extenders or stripe takers. Lexan windows are allowed, must maintain factory appearance.

Engine:
Maximum displacement for all engines is 640 CI. Small Blocks are allowed any deck height, but must remain stock bore spacing. GM Big Blocks are limited to 10.2 deck height. Ford Big Blocks are limited to 10.3 deck height. Mopar Big Blocks are limited to 10.7 deck height. Billet blocks are prohibited for both SB and BB combinations.

Transmission:
Any transmission permitted.

Turbochargers:
Single turbocharger limited to 88mm maximum (GT55-88, Pro Mod 88, ET-R88, Comp, Bullseye or =) mid frame turbo. Twin turbochargers are limited to 72mm maximum. Turbo size will be verified by measuring the housing bore at the lading edge of the impeller wheel and must maintain the contour of the compressor housing. Inducer dimensions will not exceed 3.462 inches and exducer dimensions will not exceed 4.765 inches on mid-frame turbos. Inducer dimensions will not exceed 3.462 inches and exducer dimensions will not exceed 5.560 inches on large frame turbos. The maximum diameter of the housing bore at the leading edge of the wheel may not exceed 2mm more than the maximum allowable. Inserts or reducers to achieve inlet or outlet dimensions are prohibited. Any type air-to-air or water-to-air intercooler is permitted. Turbochargers with nitrous oxide are permitted only on 2-rotor, 4-cylinder and inline-6 cylinder engines.

Superchargers:
Cog or gear driven superchargers are permitted, must meet all factory inlet, outlet and internal housing dimensions. Inserts or reducers to achieve inlet or outlet dimensions are permitted. Any type intercooler is permitted. F-1R or equivalent allowed. F-2 or equivalent allowed. F-2R is not legal. Cannot combine supercharger with nitrous. Roots supercharger limited to 10-71. Centrifugal superchargers are permitted. Screw superchargers are prohibited. No methanol cooling on blower or turbo combinations running E85 or alcohol.

Nitrous (General Rules):
Multiple bottles, must WYE together with a single -6 line. Push nitrous systems are prohibited.

Small Block Nitrous:
Permitted to run any multi-stage nitrous system.

Big Block Nitrous:
Single Stage Fogger must use -4 nitrous line maximum from WYE to solenoids. Electronic fuel injection allowed only 8 nitrous feed lines on engine. Two stage plate allowed.

Exhaust:
Mufflers or inserts are required on all cars except for turbo cars. Exhaust may exit underneath car or out the front fenders but must not affect timing or staging beams.

Fuel:
Gasoline, Alcohol or E-85 is allowed. No Methanol cooling on blower or turbo combos running E85 or alcohol. Alcohol must adhere to a 50 lb. weight penalty.

Tires:
All cars with power adder must compete on a Drag Radial type tire with the following sidewall designation 235/60/15 or a 26/8.5/15 slick.


MINIMUM BASE WEIGHTS
All minimum weights include the driver.

Naturally Aspirated

- Small Block - 2,350 lbs.
- Big Block - 2,600 lbs.

Nitrous
- Small Block - 2,600 lbs.
- Big Block (Up to 604 CI) - 3,200 lbs.
- Big Block (605 to 640 CI) - 3,250 lbs.

Supercharger
- Single YSI/F1A/6-71 Supercharger (Small Block) - 2,950 lbs.
- Single F1C/8-71 Supercharger (Small Block) - 3,100 lbs. [Deduct 50 lbs. for 8.2/8.7 Deck]

- Single F1R/Xi/10-71 Supercharger (Small Block) - 3,250 lbs. [Deduct 50 lbs. for 8.2/8.7 Deck]

- Single F1X/F2/XB105 Supercharger (Small Block) - 3,350 lbs. [Deduct 50 lbs. for 8.2/8.7 Deck]



Turbocharger

- Single 76mm T6 Turbocharger (Small Block) (Mid Frame) - 2,900 lbs.

- Single 80mm T6 Turbocharger (Small Block) (Mid Frame) - 2,950 lbs.
- Single 82mm T6 Turbocharger (Small Block) (Mid Frame) - 3,000 lbs.
- Single 84mm T6 Turbocharger (Small Block) (Mid Frame) - 3,050 lbs.
- Single 88mm T6 Turbocharger (Small Block) (Y2K or GT47-8 (Cast Mid Frame) - 3,000 lbs. [Deduct 50 lbs. for 8.2 Deck]
- Single 85mm T6 Turbocharger (Small Block) (Pro Mod 85) (Mid Frame) - 3,250 lbs. [Deduct 50 lbs. for 8.2 Deck] [Deduct 50 lbs. for Stock Valve Angle]
- Single 88mm T6 Turbocharger (Small Block) (GTX55-88, Pro Mod 88, etc. or =) (Mid Frame) - 3,300 lbs. [Deduct 50 lbs. for 8.2 Deck] [Deduct 50 lbs. for Cast Stock Valve Angle]
- Single 85mm T6 Turbocharger (Small Block) (Large Frame 85/GTX55-85) - 3,200 lbs. [Deduct 50 lbs. for 8.2 Deck] [Deduct 50 lbs. for Cast Stock Valve Angle]
- Single 88mm T6 Turbocharger (Small Block) (Large Frame 8 - 3,250 lbs. [Deduct 50 lbs. for 8.2 Deck] [Deduct 50 lbs. for Cast Stock Valve Angle]

Twin Turbochargers
- Twin 67mm Turbochargers (Small Block) - 3,250 lbs.
- Twin 72mm Turbochargers (Small Block) - 3,300 lbs.

- Buick/Olds/Pontiac: Nitrous Combos will not exceed 640 CI and must be 3,050 lbs.


WEIGHT ADDITIONS/REDUCTIONS
- Deduct 250 lbs. for Front Wheel Drive
- Deduct 100 lbs. for Mod Motor
- Deduct 25 lbs. for Leaf Springs

- Small Blocks (NOS Only) Cast Tunnel Ram/Sheet Metal/2 Carbs or 2 Throttle Bodies: Add 50 lbs.
- Deduct 50 lbs. for 2 Solenoids (1 Fuel, 1 Nitrous), 2 Spray Bar Nitrous Plate with No Line Restriction
- Deduct 50 lbs. for Blow Through Carburetor on Boosted Combinations

- Deduct 300 lbs. for Inline 6 Cylinder Turbocharged/Supercharged/Nitrous Combinations
- Deduct 150 lbs. for V-6 Turbocharged/Supercharged Nitrous Combinations
- Deduct 800 lbs. for 4-Cylinder Turbocharged/Supercharged/Nitrous Combinations



** For more information or if your combinations is not listed, you can contact Jordan Grunwald, 870-688-6686.